top of page

8HP Basics: Chapter 4 - Gear Ratio

1 day ago
7 min read

Pick the final drive around how you use the car. A track car picks it from top speed, and a street car picks it from cruising rpm.


Track Car: Choose the final drive that puts your redline at your real top speed in the gear you finish the straight in. On an 8HP that gear is usually 6th, which is direct drive (1.000), so the ratio follows from your tire size and your trap speed. It's not recommended to use 7th or 8th on track.


Drag Car: Choose a final drive that has your engine just below redline, at your expected trap speed, in 5th. The clutches associated with 6th are the weakest, so using 1-5 is more common in drag racing applications.


Street Car: Choose the final drive that gives the engine rpm you want at your usual highway speed. With the 8HP we usually set a normal cruise speed in 7th as the reference, and keep 8th for a day you are running late. A taller ratio lowers cruising rpm, and a shorter one raises it.


Our Gear Ratio & Shift Calculator shows what any ratio does in every gear. Its cruising gear mph calculator shows your rpm at highway speeds in 7th and 8th.


What the diff ratio changes, and what it can't

The final drive multiplies every gear by the same amount, so it moves your speeds and revs without changing how the gears relate to each other.


Going from a 3.15 to a 3.73 lowers the speed at any given rpm by about 16%, in every gear. In 6th, 7,000 rpm drops from 167 mph to about 141 mph. In 2nd, it drops from 53 mph to 45 mph.


So the choice comes down to one question: where do you want your rpm to land? On a track car it is redline at top speed, and on a street car it is cruising rpm on the highway.


First, here are examples where the factories landed with an 8HP:



Why the 8HP wants a taller final drive than you'd expect

Most people doing swaps already have an agressive ratio diff from a previous manual or older automatic. The 8HP is built differently, because the gearbox itself supplies the range.


A Gen 1 8HP runs from 4.714 in 1st to 0.667 in 8th, a spread of 7.07 from bottom to top. The later ratio sets spread wider, up to 8.59. The final drive multiplies all of that, so a short diff stacks on top of a 1st gear that is already deep, and it pulls the top speed of every gear down with it.


Factory ratios show where the engineers landed. Every car we checked that shipped with an 8HP uses a rear axle ratio of 3.09 or lower, and even the supercharged Dodge Hellcat gets a 2.62.


Factory ratios are chosen with fuel economy and noise in mind, so a performance build can reasonably go somewhat shorter than stock. The question is how much shorter, and that is where a 4.10 starts to cost you.


Why a 4.10 usually isn't the best choice

A 4.10 has been a very common swap pick, and plenty of builders still reach for it first. It suits a narrow set of cars, and for most it costs more than it gives back. Here it is next to the factory BMW 8HP ratio and two in-between choices, on a Gen 1 8HP with average 265 tires. Each line lists the 2.929, 3.15, 3.73 and 4.10, in that order.


  • 1st gear tops out at 7,000 rpm: 38 mph, 35 mph, 30 mph and 27 mph.

  • 6th gear reaches 7,000 rpm at: 180 mph, 167 mph, 141 mph and 129 mph.

  • 7th gear rpm at 65 mph: 2,122, 2,282, 2,702 and 2,970.

  • 8th gear rpm at 65 mph: 1,687, 1,814, 2,148 and 2,361.

  • Output shaft reaches 7,500 rpm at: 193 mph, 179 mph, 151 mph and 138 mph.


Here is what a 4.10 costs:

  • Low top speed: A 4.10 puts redline in 6th at about 129 mph.

  • It raises cruising: Street miles happen in 7th and 8th. A 4.10 puts 7th at nearly 3,000 rpm at 65 mph, about 850 rpm above the BMW ratio.

  • It means more shifts. First gear tops out at 27 mph and 2nd at 41, so each shift arrives sooner and you make more of them to reach the same speed.

  • Output Shaft Speed Risks. The output shaft reaches 7,500 rpm at 138 mph, against 193 mph with the BMW ratio. That matters if you use 7th or 8th at speed. Overspinning the output is easy if you are not careful, and this can destroy the transmission.


A 4.10 is the right call when your real trap speed is about 125 to 130 mph on a 7,000 rpm redline and you finish the straight in 6th. The worked example near the end shows that case, and a car that traps well under it can justify a 4.10 or even shorter. Most cars that trap faster than that, and most street cars, land on a lower number.


Street Car: Pick by cruising rpm

If the car lives on the road, choose the final drive by the rpm you want at highway speed, not by top speed.


Use 7th gear as the reference on an 8HP. Decide your normal cruise speed, then compare how much rpm each ratio gives you in 7th and 8th.


Lower cruising rpm is quieter and easier on fuel. Higher cruising rpm is louder, but it makes every gear accelerate harder. Taller ratios also soften acceleration from a stop, as the taller-or-shorter section below explains.


Run ratios through the calculator

Enter your tire, a candidate final drive and your transmission into our Gear Ratio & Shift Calculator, then change the ratio and watch what moves.


Then check the two charts:

  • Speed vs RPM shows where each gear's line ends, so you can see the speed every gear reaches at your redline.

  • Shift-point RPM drops shows the rpm you land on after each upshift. Look for any gear where you fall out of the engine's strong range.


Taller or shorter: what you trade

A shorter ratio, meaning a higher number like 4.10, accelerates harder in every gear but runs out of speed sooner. A taller ratio like 3.15 does the reverse.


Shorter gearing

  • Puts more torque at the wheels in every gear.

  • Reaches redline at a lower speed, so you may hit the limiter on your longest straight.

  • Raises cruising rpm. At 65 mph in 7th, a 265/35R18 turns about 2,280 rpm with a 3.15 and about 2,970 rpm with a 4.10.


Taller gearing

  • Reaches higher speeds in every gear and lowers cruising rpm.

  • Gives up wheel torque everywhere, which costs acceleration out of slow corners.

  • Can leave your top gear unused if the braking zone arrives before redline.


Check your slow corners too. Each gear tops out at a different speed on every ratio, so the gear you exit a corner in can change. On a Gen 1 8HP with 265/35R18 tires, 2nd gear tops out at 41 mph with a 4.10 and 53 mph with a 3.15.


7th and 8th gear: the output shaft speed limit

On an 8HP, treat 7th and 8th as cruising gears, because the output shaft spins faster than the engine in both.


Output shaft rpm equals engine rpm divided by the gear ratio. At 7,000 rpm in 8th (0.667), the output shaft turns about 10,500 rpm. That is why the calculator caps these two gears below your redline.


Our recommendation is to keep output shaft speed at or under about 7,500 rpm. On a Gen 1 8HP that works out to roughly 6,290 engine rpm in 7th and 5,000 in 8th. Going past it is possible, but do it with caution.


Output shaft speed is simply driveshaft speed, so it depends only on road speed, final drive and tire size, not on which gear you are in. With a 3.15 and 265/35R18 tires, the output shaft reaches 7,500 rpm at about 179 mph in any gear. With a 4.10 it arrives at about 138 mph.

That is why the final drive and this limit are linked. A very short ratio brings the recommended output limit down into the speeds you actually drive on track.


Trap Speeds

Take our N52 116i vs. our LS3 1M, both with a Gen 1 8HP's. One runs a 3.55, and the other runs a 3.08, because of their trap speed difference. A car that traps 125 to 130 could theoretically run between 4.05 and 4.22, and a car that traps 150 mph needs about 3.5 if pushing the limit.



Too Much Shifting

Surprisingly, more shifting is not always better. We have tried very short ratios in the past, and they never made us any faster.


Every shift gives up a little drive, and every downshift is another job for the driver. A shorter ratio adds shifts, because each gear covers fewer mph. With 265/35R18 tires and a 7,000 rpm redline, a 4.10 runs out of 2nd gear at 41 mph, where a 3.15 carries it to 53. Leave a 40 mph corner and accelerate to 100 mph, and the 4.10 car makes three upshifts while the 3.15 car makes two.


It is worse in a slower car, like our GLTC race car. We are not going that fast, so the braking zones are short and there is little time to get down through the gears. Downshifting three times in one braking zone is often more annoying than cool.


That extra torque is also worth less than it looks. Above slow-corner speeds, acceleration is set mostly by how much power the engine makes at that rpm, not by how much the gearing multiplies torque.


Our Suggestion

If you have a V8, or car that really isnt high strung and makes torque, use something between a 2.9-3.1. If you have a peaky engine you can start thinking about ratios a set higher. Dont go crazy with the ratio. If you have an existing diff gear on the edge, give it a try. Not using 2nd might get you what you need.



Comments


bottom of page